3 in 1 Diamond Microdermabrasion Dermabrasion Machine Water Spray Skin Wrinkle Face Peeling microdermoabrasion facial | Красота и

3 in 1 Diamond Microdermabrasion Dermabrasion Machine Water Spray Skin Wrinkle Face Peeling microdermoabrasion facial | Красота и

3 in 1 Diamond Microdermabrasion Dermabrasion Machine Water Spray Exfoliation Beauty Machine Wrinkle Face Peeling Backhead RemovalMachine

Specifications:

Name: Diamond Facial instrument 3 in 1
color: White
Net weight: 2.3kg
Voltage: 220V 50-60Hz
Power: 15W
Power: 65 VA Fuse: 2A
Package Size: 28*25*22CM
Application: Cosmetic Salon

Principle of Diamond Microdermabrasion:

● Microdermabrasion is a non-invasive, skin resurfacing procedure that gently exfoliates or polishesaway the top layer of dead skin cells by using sterile diamond heads, then the vacuum will trap the dirt or dead skin in the filtration system. It helps improve skin tone, texture and elasticity and reduces the appearance of age spots, fine lines and pigmentation etc.

● The vacuum function is used to clean the dirtin the pores through suctioning tubes. It can also increase blood circulation of the skin. It helps improving the skin elasticity and can decrease discoloration from acne and scars.

● Spray function is ideal for spraying lotion,scented water or essential oils. It can clean, purify, smooth, and stimulate the skin.

Function:

① Clean skin stratum corneum,minimize invasive scar
② Clearing blackhead and acne
③ Remove ages spots, wrinkles, hyperpigmentation, stretch marks
④ Improve dull skin and smooth skin, shrink pores, repair skin cells
⑤ Assit absorbtion of natural nutrients
⑥ Skin recovery after aggressive treatment
⑦ Increases strength of collagen and elastin fibers in the skin
⑧ Reduces redness, scar, wrinkle, inflammation and acne
⑨ Improve oily/dehydrated skin

How to use?

1. Push in the movable ring of copper nozzle at the hand piece, and pull out the 8x5 size vacuum hose. Then push in the black plastic ring on the vacuum hose.
2. Put a drop of cream or milk lotion on the vacuum hose nozzle, push in the moveable ring and insert in the vacuum hose to the limit.
3. Insert a cotton swab into the Diamond Head, then tight up the Diamond Head on the hand piece. Remove the cotton swab after every treatment.
4. Turn on the power switch.
5. Adjust the Vacuum intensity by Vacuum Regulator according to the reference table, the intensity displays on vacuum gauge and check for comfort.
6. Use the incline area of Hand piece to contact with the skin surface. Proceed with a slow sliding motion. Do not place the hand piece at one spot for too long, doing this will cause harm to the skin.
7. Adjust the crystal flow rate by Vacuum Regulator slowly from minimum to maximum. For common use, don\'t set the flow rate to maximum unless it is of necessity. This is better comfort intensity.
8. Gently stretch the skin with thumb and finger, and glide the Hand-piece 2 to 3 times over the area being treated.
Then cross again in different directions to prevent streaking lines as in the reference picture. Brush strokes or prevent streaking lines as in the reference picture. Brush strokes or polishing motions may be used in different sites.
9. After treatment, brush off all remaining dead skin with a soft brush and rinse with damp sponges or damp cool towel.
10. Allow skin to dry then apply desired skin product.
11. To clean the Diamond Head, use toothbrush or cotton swab damped with a little alcohol to wipe off the dirty impurity, and then use UV light or high temperature for sterilization.

Package Included:

1 x Diamond Dermabrasion Machine

1 x PVC vacuum hose 8*5

3 x Diamond Wands

9 x Diamond Tips

1 x Heads box & foam

3 x O-rings

2 package x Cotton Filter

1 x Power cord

1 x Manual

2 x Spray Bottle

3 x Glass Tubes