MOOL for Kakute F4 V2 STM32F405 Flight Controller with Betaflight OSD RC Multi-Rotor FPV Racing Drone |

body { font-size: 75%; color: #000; font-family: Open Sans,Arial,Helvetica,sans-senif,SimSun,"宋体"; line-height: 1.3; } dl { margin: 0px; width: 480px; float: left; } dt { width: 100px; height: 15px; float: left; } dd { width: 240px; height: 15px; float: left; } dl dt { margin: 0px; line-height: 22px; color: #474747; font-size: 14px; font-family: tahoma; } #product-desc { width: 100%; height: 209px; } #description { width: 100%; height: 50%; } #details { width: 100%; height: 50%; } .ui-box-title { height: 30px; font-size: 15px; font-family: tahoma; font-weight: bold; background-color: #ddd; text-anchor: inherit; padding-top: 8px; margin: 0px; } .ui-box-body { margin: 0px; } #tbspecifics { border-right: 1px solid black; border-bottom: 1px solid black; } #tbspecifics tr { height: 30px; } #tbspecifics td { width: 100px; border-left: 1px solid black; border-top: 1px solid black; } The for Kakute F4 flight controller supports important features of Betaflight/Cleanflight, such as OSD and Dshot. The faster.for F4 processor gives room for future feature development: run all features at the fast 8 kHz PID loop rate, at single-digit CPU utilization!Because of issues with serial inversion, other for F4 boards struggle to support protocols such as FrSky SBUS and SmartPort at the same.
time. The for Kakute F4 is designed to support all serial protocols at once.New V2 Features:Additional UART(UART 4)added to support serial camera communication such as to RunCam Split. Please note this is NOT.the same as Betaflight Camera Control feature,which controls the menu of FPV cameras like Swift,etc.
Additional UART (UART 5) added to support ESC telemetry such as from BLHeli_32 and KISS.Through-hole solder pads instead of flat pads for more secure soldering especially for beginners.
Barometer sensor on board allows altitude hold mode.I2C pad available for certain external sensors.Supports Betaflight and Cleanflight.Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level,all using your transmitter sticks and goggles.Soft-mounting built in. The IMU ("gyro") chip on this board is mounted on vibration-isolating foam.
This means that there is no need.to soft-mount the board itself.New high-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz.2 oz. copper PCB allows up to 120A maximum continuous current.Dedicated bootloader button for easy firmware flashing.Low-profile design fits into even very compact frames.Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on "B+" pad only).
Tool Supplies: Grinded
Remote Control Peripherals/Devices: Receivers
Use: Vehicles & Remote ControlToys
Four-wheel Drive Attributes: Motors
Technical parameters: Value 2
Wheelbase: Screws
For Vehicle Type: Airplanes
Upgrade Parts/Accessories: Adapter
RC Parts & Accs: Motor Components
MCU: STM32F405RGT6 32-bit processor
IMU: ICM20689 (SPI)
Barometer: BMP280
USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
5 hardware UARTS (UART1,3,4, 5, 6)
Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
128 Mbit Dataflash chip for Blackbox logging
Mounting Holes: Standard 30.5mm square to center of holes
Weight: 7g
Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F4 AIO monitors voltage
directly from the battery power lead.
Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 1.5 amps and 3.3v at up to 200 mA to power
peripherals such as receiver, video transmitter, FPV camera, or LED strip.
Supports BLHeli pass-through for easy ESC upgrade and configuration.
colour:black
Material:ABS + metal
size:35x30x8mm (includes USB in height)
Package Contents:
1*Flight controller
Only the above package content, other products are not included.
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.